|
click here
|
|
|
|
 |
|
Tank Mixers are designed, engineered and
built to provide long, trouble free service
in blending and mixing applications. Our
mixers are used to blend liquids, suspend
or dissolve solids, and dispense immiscible
liquids in a wide variety of industrial
applications. Some common mixer models are
listed below, but other customized designs
are available. Contact us for details.
Mixers can be used with either Flat Bottom
or Cone Bottom Tanks. Although commonly
associated with Open Top Tanks, they can
be used with Closed Top Tanks as well. See
our (Vertical Bulk Storage), (Open Top Cylindrical),
(Closed Top Cone Bottom), and (Open Top
Closed Bottom) Tank sections to select a
Tank and an “AM” Stand to be
used with your mixer. Mixers are sold separately
as well.
|
|
|
|
Mixer Selection Chart
Our chart is intended to furnish basic guidelines for selecting the proper mixer to provide a mild blending of liquids of various viscosities in different size tanks. This information is based on an approximate 30 minute mix-blend time for two liquids when both liquids are already in the tank. Mixing times can be shortened if one liquid is added while the first liquid
is already being mixed. Powders should always be added while mixer is running.
VISCOSITY
(CPS) |
TANKS UP
TO
50 GAL |
TANKS UP
TO
100 GAL |
TANKS UP
TO
200 GAL |
TANKS UP
TO
500 GAL |
TANKS UP
TO
1,000 GAL |
|
Mixer Part # |
Mixer Part # |
Mixer Part # |
Mixer Part # |
Mixer Part # |
= or < 1 |
CTBN 10 |
CTBN 10 |
CTBN 10 |
CTBN 10 |
CTJG 10 |
= or < 100 |
CTBN 10 |
CTBN 10 |
CTBN 20 |
CTJG 10 |
CTJG 10 |
= or < 300 |
CTBN 10 |
CTBN 20 |
CTJG 10 |
CTJG 10 |
CTJG 20 |
= or < 500 |
CTBN 20 |
CTJG 10 |
CTJG 10 |
CTJG 10 |
CTJG 30 |
= or < 1000 |
CTBN 20 |
CTJG 10 |
CTJG 20 |
CTJG 20 |
CTJG 40 |
= or < 2000 |
CTJG 10 |
CTJG 10 |
CTJG 30 |
CTJG 30 |
CTJG 51 |
NOTE: Optimum mixing will be achieved when the mixer is angled from the tank wall. "Angling-Off" center is preferred when good material turnover is required, as in mixing a slurry. "Angling-On" center is desirable for a gentle mixing action or when vortexing must be minimized. Improper mounting of a mixer can greatly lessen mixing efficiency, cause vibration, and possible damage the mixer.
(See Figures Below)
|
|
MIXER
SPECIFICATIONS |
CTBN
10 & 20 Models
Direct drive-small batch mixing.
316 S.S. Shafts and propellers.
Coupling fully enclosed for safety.
Clamp adjusts to any angle.
CTJG 10, 20, 30, 40 & 51 Models
350 RPM gear-driven.
316 S.S. shafts and propellers.
1.0 pitch ratio marine propellers.
Enhanced flow co-efficient and power
Adjustable shaft angle to achieve
optimum mixing for various processing
needs (see figures below)
Motors are Totally Enclosed, Fan Cooled
(TEFC) *Explosion Proof Available
Permanent lubricated gears and shaft
bearings.
Available with air motors for use
in flammable, or explosion-proof environments.
|
|
 |
NOTE:
SHAFT LENGTHS CAN BE ADJUSTED
MIXER
PART # |
MOTOR
SPECS |
SHAFT
LENGTH |
LENGTH
OF GEAR
DRIVE AND/OR MOTOR |
TOTAL
LENGTH |
PROPELLER DIA. |
SHAFT DIA. |
CTBN 10 |
1/4 H.P. 115/230 |
30" |
14" * |
44" |
4" |
1/2" |
CTBN 20 |
1/3 H.P. 115/230 |
32" |
14" * |
46" |
4" |
1/2" |
CTJG 10 |
1/4 H.P. 115/230 |
48" |
21 1/16" |
69 1/16" |
8" |
3/4" |
CTJG 20 |
1/3 H.P. 115/230 |
48" |
21 5/8" |
69 5/8" |
10" |
3/4" |
CTJG 30 |
1/2 H.P. 115/230 |
48" |
22 1/2" |
70 1/2" |
12" |
3/4" |
CTJG 40 |
3/4 H.P. 115/230 |
60" |
22 3/4" |
82 3/4" |
13" |
3/4" |
CTJG 51 |
1 H.P. 230/460 |
60" |
22 3/8" |
82 3/8" |
14" |
1" |
|
|
|
| |
| |
|
Search Archive
Submit Questions
Today's Tip
Tip
|
|
 | | |
|
